APC RAID Subsystem SCSI-SATA II Informações Técnicas Página 72
- Página / 259
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Using the RAID GUI
2-47
Record Event Log
Click Configure and specify the Lowest severity of events option for the events you want to record on NVRAM. The
events with severity levels higher than the specified one will be recorded. The default severity level is info, which means
events of all severity levels will be recorded.
Send a Test Mail
Click Configure and specify the Severity of testing event option to send a test mail. A testing event record will be
generated according to the selected severity level. This helps users to test the event logging and notifications setup.
2.9.4 UPS
The UPS Control option enables or disables the UPS function when the controller is started. When this option is set to
On, the controller will automatically detect if the UPS is connected or not.
To configure the UPS settings, do the following:
1. Select Event management > UPS from the main menu, you can view the UPS information, status, and battery status
here.
2. Click Configure and specify the following options.
3. Click Apply to confirm the current settings.
2.9.5 Miscellaneous
Note
Before sending out the test mail, you need to turn on the event notification and specify the event
receivers. (Refer to 2.9.1 Setting up the SMTP on page 2-44.)
Change Date (YYYY/MM/
DD)
This option resets the latest battery replacement date.
Delay Shutdown
(seconds)
90 / 180 / 270 / 360 / 450 / 540 / 630
When a power failure occurs and the UPS battery charge is below the normal
range, the UPS will power down after the specified delay time.
Delay Boot (seconds) 0 / 60 / 120 / 180 / 240 / 300 / 360 / 420
The UPS automatically powers on after the specified delay time. This avoids
branch circuit overload when AC power returns.
Low Battery Threshold
(seconds)
120 / 300 / 480 / 660 / 840 / 1020 / 1200 / 1380
This option notifies the user that the UPS battery is low, with the specified
remaining seconds.
Change Restart
Percentage
0 / 15 / 30 / 45 / 60 / 75 / 90
After the AC power returns, the UPS does not power on until the battery charge
reaches the specified capacity.
Note
1. The values from each drop-down menu may be different according to the UPS connected.
2. Currently the controller only support and communicate with Smart-UPS function APC
(American Power Conversion Corp.) UPS. Please check detail http://www.apc.com/.
Beeper Control: On (default) / Off / Mute
This option controls the controller’s beeper.
On: The beeper sounds during exceptional conditions or when background tasks make progress. By default, the
beeper is on.
Off: The beeper is quiet all the time.
Mute: This temporarily mutes the beeper, but it beeps again if exceptional conditions still exist.
Auto Write-Through Cache
- U320 SCSI to SATAII 1
- 4G Fibre to SAS 1
- SAS to SAS 1
- Disk Array Systems 1
- JanusRAID II Generic 3
- Software Manual 3
- Table of Contents 5
- Contents 10
- List of Tables 11
- List of Figures 12
- About this manual 15
- Symbols used in this manual 15
- Chapter 1: Introduction 17
- 1.2 Key Features 18
- 1.3 How to Use This Manual 21
- 1.4 RAID Structure Overview 22
- Introduction 24
- Chapter 2: Using the RAID GUI 26
- Using the RAID GUI 27
- • Firefox language settings 27
- 2.1.2 Multiple System Viewer 28
- 2.2 Monitor Mode 29
- 2.2.1 HDD state 30
- 2.2.2 Information icons 31
- 2.2.3 Rear side view 32
- 2.2.4 Login 35
- 2.3.3 Monitor mode 38
- 2.3.4 Information icons 38
- 2.4 Config Mode 39
- 2.5 Quick Setup 40
- 2.6 RAID Management 41
- 2.6.2 JBOD 42
- 2.6.3 Disk groups 43
- • Delete disk groups 44
- • Modify disk groups 44
- 2.6.4 Logical disks 45
- • Delete logical disks 46
- • Modify logical disks 46
- 2.6.5 Volumes 47
- 2.6.6 Snapshot Volumes 48
- 2.6.7 Storage provisioning 50
- • Symmetric method 51
- • Selective method 53
- 2.7 Maintenance Utilities 54
- 2.7.6 Expanding volumes 57
- 2.7.7 Shrinking volumes 57
- 2.7.8 Cloning hard disks 58
- 2.7.9 Scrubbing 58
- 2.7.12 Array roaming 60
- 2.7.13 Array recovery 60
- • Partition state transition 61
- • Start a recovery 61
- 2.7.14 Schedule task 62
- 2.7.15 Cache Configurations 62
- 2.7.16 Miscellaneous 62
- 2.8 Hardware Configurations 63
- 2.8.2 Ports 65
- 2.8.3 COM port 68
- 2.9 Event Management 69
- • SNMP MIB Definition 70
- 2.9.3 Event logs 71
- 2.9.4 UPS 72
- 2.9.5 Miscellaneous 72
- 2.10 System Management 73
- 2.10.4 System Time 76
- 2.10.5 Security control 76
- 2.10.6 System information 77
- 2.10.7 Battery backup module 77
- 2.10.10 Miscellaneous 78
- 2.11 Performance Management 79
- 2.11.3 LUN 80
- 2.11.4 Storage port 80
- Using the LCD Consolel 82
- 3.2 LCD Messages 83
- 3.2.3 Emergent info 84
- 3.2.5 Hotkeys 85
- 3.3 Menu 86
- 3.3.4 Terminal Port Settings 87
- 3.3.5 System Settings 87
- 3.3.6 System Information 87
- 4.1 Overview 88
- 4.2 Basic RAID Management 89
- 4.2.3 Disk groups 90
- 4.2.4 Spare and rebuild 90
- 4.2.5 Logical disks 91
- 4.2.7 Volumes 92
- 4.2.8 Cache 92
- 4.3.3 Task priority control 95
- 4.4 Storage Presentation 97
- 4.4.3 Storage groups 98
- 4.4.4 Presentation planning 99
- 4.5.1 Generic hard disk 100
- Using the CLI Commands 101
- 4.5.2 SAS ports 102
- 4.5.3 SCSI ports 102
- 4.5.4 FC ports 103
- 4.5.6 Local terminal ports 105
- 4.5.7 Enclosure 105
- 4.5.9 iSCSI target / ports 106
- 4.6 Performance management 108
- 4.6.4 Storage ports 109
- 4.8 Event Management 110
- 4.8.3 Event handling 111
- 4.9 System Management 112
- 4.9.2 Time management 113
- 4.9.4 System information 114
- 4.9.5 Miscellaneous 115
- 4.10.1 Lookup RAID systems 116
- 4.12 Snapshot 117
- Chapter 5: Advanced Functions 119
- Advanced Functions 120
- 1 2 3 4 5 6 121
- 7 8 9 10 11 12 121
- • MPIO Device Information 123
- • Manage multipathd service 126
- 5.2 Multiple ID solutions 128
- 5.3 Redundant Controller 129
- Host Group 0 133
- Host Group 1 134
- • GUI Notification 139
- 5.4 Snapshot 140
- • Spare COW Volume 141
- • Restoring by Snapshots 141
- • Online Volume Expansion 141
- 5.4.3 How to Use Snapshots 142
- • Snapshot Roaming 144
- 5.5.2 Logical disk shrink 146
- 5.5.3 Logical disk expansion 147
- 5.5.4 Disk group expansion 148
- • Do extend a partition: 150
- • Do shrink a partition: 150
- 5.6 RAIDGuard Central 151
- 5.6.2 Deployment Overview 152
- • Windows OS platform 153
- • Mac/ Linux OS platform 153
- 5.6.6 RGC GUI Overview 155
- 5.6.8 RAID System Monitoring 160
- 5.7 VDS Provider 161
- • Register RAID systems 163
- • Microsoft DiskRAID 163
- • Emulex EZPilot 164
- Chapter 6: Troubleshooting 165
- 6.3 Performance Tuning 166
- 6.4 Hard Disks 167
- 6.5 User Interfaces 168
- Troubleshooting 169
- A.1 RAID Overview 173
- A.2 RAID 0 174
- A.3 RAID 1 175
- A.4 RAID 3 176
- A.5 RAID 5 177
- A.6 RAID 6 178
- A.7 RAID 10 179
- A.8 RAID 30 180
- A.9 RAID 50 181
- A.10 RAID 60 182
- A.11 JBOD 183
- A.12 NRAID 184
- B.1 Overview 185
- Appendix 186
- Appendix C: Boot Utility 194
- C.1 (N) Set IP address 195
- C.2 (L) Load Image by TFTP 195
- C.3 (B) Update Boot ROM 196
- C.4 (S) Update System ROM 197
- C.5 (H) Utility menu 197
- C.6 (P) Set password 197
- C.7 (R) Restart system 197
- D.1 RAID 198
- • Initialization 200
- • Spare 201
- • Rebuild 202
- • Roaming 202
- • Recovery 203
- • Write Cache 204
- D.2 Task 205
- • Logical disk migration 206
- • Logical disk shrink 209
- • Disk group defragmentation 209
- • Volume expansion 210
- • Disk cloning 210
- D.3 Disk 219
- • Disk port and chip 221
- • SMART disk self tests 222
- • Bad block handling 223
- • On-disk metadata 225
- • Disk Cache 227
- D.4 Host ports 228
- • IO exceptions handling 229
- • Port and chip 229
- • Hosts 230
- • iSCSI 235
- D.5 Controller hardware 237
- D.6 Enclosure 239
- • Voltage 240
- • Power supply 242
- D.7 System 246
- • Security control 247
- • Events 248
- • Firmware update 250
- • Email (SMTP) server status 251
- • Miscellaneous 252
- • Fail-back 253
- D.8 Network 255
- • iSCSI port 256
- D.9 Miscellaneous 257
- D.10 Snapshot 257
Manuais e produtos relacionados com Redes APC RAID Subsystem SCSI-SATA II
Redes APC AP9613 Manual de Instalação
(36 páginas)
(36 páginas)
Redes APC AP9470 Manual de Instalação
(32 páginas)
(32 páginas)
Redes APC AP9622 Manual de Instalação
(28 páginas)
(28 páginas)
Redes APC IP DSLAM Guia do Utilizador
(603 páginas)
(603 páginas)
Redes APC RAID Subsystem SCSI-SATA II Especificações
(100 páginas)
(100 páginas)
Redes APC RAID Subsystem SCSI-SATA II Especificações
(94 páginas)
(94 páginas)
Redes APC AP9606 Manual de Início Rápido
(20 páginas)
(20 páginas)
Redes APC AP9312TH Guia do Utilizador
(32 páginas)
(32 páginas)
Redes APC AP9608 Manual de Instalação
(32 páginas)
(32 páginas)
Redes APC 66123 Manual de Instalação
(16 páginas)
(16 páginas)
Redes APC AP9630 Guia do Utilizador
(85 páginas)
(85 páginas)
Redes APC IP DSLAM Guia do Utilizador
(67 páginas)
(67 páginas)
Redes APC AP9630 Manual do Utilizador
(117 páginas)
(117 páginas)
Redes APC Network Management Card Guia do Utilizador
(118 páginas)
(118 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 1.535 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais