APC RAID Subsystem SCSI-SATA II Especificações descarregar pdf (Página 24)

Chapter 1: Introduction

1.4.3 Normalized Airflow

Proper subsystem cooling is referred to as “normalized” airflow.

Normalized airflow ensures the sufficient cooling of the subsystem and is

only attained when all components are properly installed. Therefore, a failed

component should only be hot-swapped when a replacement is available. If

a failed component is removed but not replaced, permanent damage to the

subsystem can result.

Hot-swappable Components

1-13

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 93 94

Falcon II 1
Installation and Hardware 1
Reference Manual 1
Warnings and Certifications 3
CB (Certified Worldwide) 4
Table of Contents 4
NSTALLATION 5
Safety Precautions 7
About This Manual 8
Revision History 8
Who should read this manual? 8
Conventions 9
Software and Firmware Updates 10
This page is intentionally 11
Chapter 1 12
Introduction 12
1.1.2 Enclosure Chassis 13
1.1.2.3 Front Panel Overview 14
1.1.2.5 Rear Panel Overview 15
1.2.1 LCD Panel 16
1.2.2 Drive Trays 17
WARNING! 17
1.2.6 DIMM Module 19
1.2.7 BBU 19
1.2.8 Power Supply Units 20
1.2.9 Cooling Modules 21
1.3 Subsystem Monitoring 22
1.3.4 Audible Alarms 23
WARNING: 23
1.4.2 Components 23
Chapter 1: Introduction 24
Chapter 2 26
Hardware Installation 26
2.3 Safety Precautions 27
CAUTION! 28
2.5 Unpacking the Subsystem 30
2.6 Installation Overview 31
2.7 BBU Installation 31
2.7.3 Installation Procedure 32
2.8 Hard Drive Installation 34
2.9 Drive Tray Installation 37
Chapter 3 40
Subsystem Monitoring 40
3.2 Status Indicating LEDs 41
3.2.2 LCD Panel 42
3.2.3 Drive Tray LEDs 43
3.2.4 Controller Module LEDs 44
3.2.5 LAN Port LEDs 46
3.2.6 BBU Module LED 46
3.2.7 PSU LEDs 46
3.2.8 Cooling Module LEDs 47
3.3 Audible Alarm 48
C Monitoring 49
Chapter 4 50
4.2 Host Connection Topology 51
4.3 Daisy Chain 52
4.3.2 Daisy Chain Procedures 53
4.4 Power On 54
4.4.3 Power On Status Check 55
4.4.4 LCD Screen 56
FALCON II 56
4.5 Power Off Procedure 57
Chapter 5 58
Subsystem Maintenance 58
5.3 DIMM Module Replacement 62
White Clip White Clip 63
5.5.1 PSU Module Overview 65
PSU Handle 67
5.6.1 Cooling Module Overview 68
Side latches 69
Silver Handle 69
5.7.2 Replacing a Hard Drive 71
5.8 Replacing a Dongle Kit 73
Appendix A 74
Uninterruptible Power Supply 74
A.4.2 Set the Baud Rate 75
A.4.3 Connect COM2 75
A.5 Power On 76
A.6 UPS Status Monitoring 76
A.6.3 UPS Message Summary 78
Appendix B 80
Specifications 80
Appendix B: Specifications 82
Aliases for Target IDs 82
Controller Specifications 83
B.6 RAID Management 85
Appendix C 87
Spare Parts and Accessories 87
C.2 Accessories 88
Appendix D 89
Pin Outs 89
D.2 DB9 Audio Jack Pin Outs 90
D.4 Null Modem 91
D.5 Ethernet Port Pin Outs 92
D.6 Main Power 92
Index - 1 93
Index - 2 94

Comentários a estes Manuais

Sem comentários

APC RAID Subsystem SCSI-SATA II Especificações Página 24

Comentários a estes Manuais

Manuais e produtos relacionados com Redes APC RAID Subsystem SCSI-SATA II