APC IP DSLAM Guia do Utilizador Página 25
- Página / 603
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
ADSL2/2+ IP DSLAM
17
of two or more buildings. If products installed in separate building are
interconnected, the voltage potential can cause a hazardous condition.
Consult a qualified electrical consultant to determine whether or not this
phenomenon exists and, if necessary, implement corrective action before
interconnecting the products. If the equipment is to be used with
telecommunications circuit, take the following precautions:
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet location unless the jack is specially
designed for wet location.
Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.
Use caution when installing or modifying telephone lines (other than a
cordless telephone) during an electrical storm. There is a remote risk of
electric shock from lightning.
Do not use a telephone or other equipment connected to telephone lines to
report a gas leak in the vicinity of the leak.
4.3.2 ADSL2/2+ IP DSLAM Rear Panel Connection
The following figure shows the rear panel connection of ADSL2/2+ IP
DSLAM:
Figure 2-1 ADSL2/2+ IP DSLAM Rear Panel Connection
Step 1: Ground the ADSL2/2+ IP DSLAM by connecting a grounded wire
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Manuais e produtos relacionados com Redes APC IP DSLAM
Redes APC RAID Subsystem SCSI-SATA II Especificações
(100 páginas)
(100 páginas)
Redes APC RAID Subsystem SCSI-SATA II Especificações
(94 páginas)
(94 páginas)
Redes APC AP9606 Manual de Início Rápido
(20 páginas)
(20 páginas)
Redes APC AP9312TH Guia do Utilizador
(32 páginas)
(32 páginas)
Redes APC AP9608 Manual de Instalação
(32 páginas)
(32 páginas)
Redes APC 66123 Manual de Instalação
(16 páginas)
(16 páginas)
Redes APC AP9630 Guia do Utilizador
(85 páginas)
(85 páginas)
Redes APC IP DSLAM Guia do Utilizador
(67 páginas)
(67 páginas)
Redes APC AP9630 Manual do Utilizador
(117 páginas)
(117 páginas)
Redes APC Network Management Card Guia do Utilizador
(118 páginas)
(118 páginas)
Redes APC AP9630 Manual do Utilizador
(32 páginas)
(32 páginas)
Redes APC AP9224110 Especificações
(16 páginas)
(16 páginas)
Redes APC AP9608 Especificações
(9 páginas)
(9 páginas)
Redes APC AP9608 Manual do Utilizador
(4 páginas)
(4 páginas)
Freecom Technologies Skype Phone Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Telefone Freecom Technologies Skype Phone.
Wir stellen 1 PDF-Handbücher Freecom Technologies Skype Phone zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentários a estes Manuais